WiseFab - Nissan 350Z Front Lock Kit
65 degrees of lock, parallel steering. As an option, there would be a possibility to buy Ackermann adjustment kit. You could tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment.
About the same weight as original aluminium suspension. All the metal components on 350Z front suspension are from high strenght steel, including sheetmetal components, tubes, tube ends and rod end housings. Rod ends and spherical bearings are used, no rubber bushings.
Lower links are replaced with one arm. 2 lower links would have some benefits for circuit racing, but for drifting with higher steering angle the stiffness and packaging would become an issue. Therefore lower one piece arm is used.
Higher roll center (RC). Lowering the driftcar is a must to increase performance and handling, but this would mess up the original factory designed kinematics. It lowers the roll center and increases camber gain. On knuckle, both joints are dropped, which brings the front RC up on lowered car, providing higher roll stiffness and letting to remove the front anti roll bar (sway bar) that is quite difficult to package with that high lock angles.
Very good camber control and minimal bump steer with high steering angles. On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.
Steering jacking control. During steering the car chassis is moving up and down – this is called jacking. Steering jacking is caused by combination of caster, KPI, trail and scrub. On road cars, this effect is used sometimes to balance the car or to help to turn in. During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry that it doesn’t cause any handling issues.
Consistent and predictable self-alignment torque. Caster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock.
Adjustable spring and shock absorber motion ratio. The shock lower bracket has 3 attachment possibilities, which allows to change suspension stiffness and handling very quickly.
Ackerman kit included
Other components, packaging and clearance.
This kit assumes coilovers to have enough clearance.
Ride height is designed to be ~80mm from front subframe to ground
Dependent on rim width and ET, wider fenders or fender flares would be needed.
Inner wheel wellsdo not need to be modified with tire diameter up to 635mm (215/45R17, 225/45R17, 235/40R17, 225/40R18 etc). Minimum rim diameter is 17”.
Recommended backspacing is ~135mm (7“ ET45; 8“ ET35; 9“ ET20). If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.
The kit is designed and manufactured the way that after installation and toe adjustment it’s ready to use right away.
Our team at Bleeding Tarmac is working hard to offer you the best prices and the lowest shipping cost. Because we are offering products at MAP, we unfortunately have to charge shipping fees on some items.
Honesty is the best policy - Let's be honest, shipping is not easy and can be pricy. Here at Bleeding Tarmac, we will not hide shipping cost in sale prices. Our automated check out service provides the best estimate, but don't be shy and contact us to get the lowest shipping quote possible.
If you have specific shipping needs, please contact us before ordering.
Oversized, overweight and/or special items may require additional shipping fees and include, but are not limited to : rollcage kits, batteries, seats, tires and wheels. You will be contacted with the actual shipping charges before your order is processed.
Where do we ship?
We ship to Alaska, Hawaii, and Canada. Please contact us to get a shipping quote.
International customers are responsible for all duties, fees, and taxes associated with their shipments.
All regular items usually ship within 1 to 10 business days.
To accelerate the shipping process, parts will be shipped from remote warehouses located throughout the United States. Orders may ship in multiple boxes and/or from multiple carriers.
Special orders or out of stock items may take longer and we will inform the customer by email once we have a estimated delay.
Items are carefully packed and sealed to prevent damage in transit. Loss or damage claims must be taken up with the carrier. If a shipment is lost, mis-routed, or damaged we will start an investigation with the shipping carrier. Replacement items cannot be sent until the shipping carrier completes their investigation.
Fluids & Fire Suppression Systems
Shipping restrictions apply to all fluids and fire suppression systems. These items will only be shipped by ground.
ADDED Shipping fees might be required after ordering BRAID WHEELS.
Because of the container shortage and unreliable delays of maritime transport, we only drop ship wheels directly from the manufacture in Spain at the moment.
Shipping fees calculated at check out are ESTIMATED only.
Customer will be contacted after completing the order, BUT before we process payment, to confirm availability, shipping options, and rate.
** Return & Cancellation are usually impossible since most wheels are made to order. Cancellations are ONLY possible if made BEFORE the production begins. Please contact us to verify if anything is possible. **
Unless in stock, order lead time : 4 to 10 weeks
Longer lead times apply during the rebuild season.
Samsonas products are often customized for your car and are shipped from Europe, therefore lead times can vary and occasional delays can occur.
Please order with plenty of time in advance.
Cancellation fee 25%
All Rally Innovations products requires a signature on delivery.
In stock Items will be shipped within 5 business days. Customer will be contacted if shipping delay is expected to be longer.
Cancellations may be allowed under certain conditions. Once the order has been packaged and a tracking number has been created a cancellation will not be allowed. Special order items cannot be canceled at anytime once the order is processed.
If you refuse or return your delivery, the buyer will be responsible for the original shipping charges. Exchanged items will be charged shipping fees.
Our team is here to assist you in your purchase. Please take advantage of our knowledge before you order.
Within 30 days from the receipt of you order, certain items can be approved for return if unused, uninstalled, undamaged, and in the original packaging. Items must include all hardware, instructions, tags, or other original included accessories.
All returned items must be approved and issued an RMA number (returned merchandise authorization). No credit will be issued without a RMA number.
Items must be properly packaged for shipping. We reserve the right to charge a restocking fee or decline issuance of credit for damaged retail packaging. Customer is responsible for return shipping fees.
Please use a trackable service for you return such as UPS, FedEx, or certain USPS services. Return shipments should be insured for the proper amount. Bleeding Tarmac will not be held responsible for returns that are lost or damaged in shipping.
Once the item is received and inspected, a credit will be issued. Refunds may take 3-5 business days to post on your account.
All refunds are subject to a processing and/or restocking fee.
No returns on the following: Special order items, helmets, clothing articles, items considered clearance or close-outs, or items with special pricing, are final sale and may not be returned.
Apparel and promotional items
All apparel and promotional items, including hats, t-shirts, sweatshirts, stickers... are final sales. No returns, exchanges, or refunds will be issued on these items.
We offer no warranty above that of the manufacturer of goods sold. In an effort to minimize legalese we offer the following statement. Each brake parts manufacturer warrants it's goods to be fit and free from defects in materials and workmanship. This is quite limiting. Any warranty above and beyond that is strictly on a case by case basis and limited to replacement of equal value only.
Coupon codes can only be redeemed at the time of purchase. Once an order is placed we will not price match any other competitors, all price matching must be negotiated before an order is placed.
We reserve the right to refuse any order for whatever reason, without being liable for any damage or costs.
Most products on our websites are designed for off-road use, and to be used at the purchaser’s own risk and discretion. Bleeding Tarmac, Broken Motorsports, or any of its companies are exempt from any liability, and will be held harmless for any damage incurred, either property damage or personal harm, by the use of any of these products, whether being used for off-road use, or for use on public roads. While some of these products may be legal for use on public roads, Bleeding Tarmac, Broken Motorsports, or any of its companies do not endorse, authorize, or sanction their use on such public roads.