Killer B Motorsport - Ultimate FA20 Subaru WRX Oil Pickup
The OEM pickup screen is crimped in a retainer and that assembly is spot welded into the pickup ‘can’. There are a couple of flaws with this process. One is that the screen is creased where the retaining ring is crimped over it. The other is the spot weld process embrittles the screen. We pushed on the screen of new OEM pickups, and several popped wire strands, without a lot of effort.
Being known for making the best Subaru Performance Oiling Products money can buy, addressing this was right up our alley. Of course, our own spin of improvements, besides the obvious had to be made to assure set it and forget reliability that comes with our products. A means for improving performance was taken advantage of during the design process as well.
The obvious big change is the tube has no bend. No bend means no restriction, and even better coming from the OEM tube because it uses a more restrictive pinch bend. The ID of the tube has been increased, and so has the thickness. The angle of the tube points it directly at the inlet into the block. Like our EJ engine Ultimate Oil Pickup this one too uses a screen to match the OEM spec opening size of the mesh. Although, we use a higher strength screen material. The screen area has been increased over 31% which reduces the restriction and stress on the screen. Our screen is lightly pressed and welded into place assuring the wire does not gets stresses or heat damages. TIG welding throughout assures proper weld penetration and quality. The material is 4130 Alloy Steel to further provide an increase in strength over the brazed stamped steel OEM version. The units have been pressure tested to 150psi over the face of the screen without issue.
Killer B Motorsport has many years of being at the forefront of Subaru Oiling system performance. Improvements have been made to the oil pickup design to improve the oil flow characteristics and addresses the screen design to eliminate the process that causes screen failure with the OEM units.
• Tube features larger inside diameter and thicker wall for increased flow capacity and strength.
• No bends provide maximum flow potential (OEM unit uses a restrictive punch bend).
• Screen flow area increased by over 31% to improve flow, reduce restriction.
• Made from 4130 High Strength Alloy Steel for never fail reliability
• Hand TIG welded
• Made in the USA
NOTE: This part number WILL NOT work with BRZ/FR-S. This is only for 2015+ WRX FA20
|Vehicle Fitment||2015+ Subaru Impreza WRX|
Our team at Bleeding Tarmac is working hard to offer you the best prices and the lowest shipping cost. Because we are offering products at MAP, we unfortunately have to charge shipping fees on some items.
Honesty is the best policy - Let's be honest, shipping is not easy and can be pricy. Here at Bleeding Tarmac, we will not hide shipping cost in sale prices. Our automated check out service provides the best estimate, but don't be shy and contact us to get the lowest shipping quote possible.
If you have specific shipping needs, please contact us before ordering.
Oversized, overweight and/or special items may require additional shipping fees and include, but are not limited to : rollcage kits, batteries, seats, tires and wheels. You will be contacted with the actual shipping charges before your order is processed.
Where do we ship?
We ship to Alaska, Hawaii, and Canada. Please contact us to get a shipping quote.
International customers are responsible for all duties, fees, and taxes associated with their shipments.
All regular items usually ship within 1 to 10 business days.
To accelerate the shipping process, parts will be shipped from remote warehouses located throughout the United States. Orders may ship in multiple boxes and/or from multiple carriers.
Special orders or out of stock items may take longer and we will inform the customer by email once we have a estimated delay.
Items are carefully packed and sealed to prevent damage in transit. Loss or damage claims must be taken up with the carrier. If a shipment is lost, mis-routed, or damaged we will start an investigation with the shipping carrier. Replacement items cannot be sent until the shipping carrier completes their investigation.
Fluids & Fire Suppression Systems
Shipping restrictions apply to all fluids and fire suppression systems. These items will only be shipped by ground.
ADDED Shipping fees might be required after ordering BRAID WHEELS.
Because of the container shortage and unreliable delays of maritime transport, we only drop ship wheels directly from the manufacture in Spain at the moment.
Shipping fees calculated at check out are ESTIMATED only.
Customer will be contacted after completing the order, BUT before we process payment, to confirm availability, shipping options, and rate.
** Return & Cancellation are usually impossible since most wheels are made to order. Cancellations are ONLY possible if made BEFORE the production begins. Please contact us to verify if anything is possible. **
Unless in stock, order lead time : 4 to 10 weeks
Longer lead times apply during the rebuild season.
Samsonas products are often customized for your car and are shipped from Europe, therefore lead times can vary and occasional delays can occur.
Please order with plenty of time in advance.
Cancellation fee 25%
All Rally Innovations products requires a signature on delivery.
In stock Items will be shipped within 5 business days. Customer will be contacted if shipping delay is expected to be longer.
Cancellations may be allowed under certain conditions. Once the order has been packaged and a tracking number has been created a cancellation will not be allowed. Special order items cannot be canceled at anytime once the order is processed.
If you refuse or return your delivery, the buyer will be responsible for the original shipping charges. Exchanged items will be charged shipping fees.
Our team is here to assist you in your purchase. Please take advantage of our knowledge before you order.
Within 30 days from the receipt of you order, certain items can be approved for return if unused, uninstalled, undamaged, and in the original packaging. Items must include all hardware, instructions, tags, or other original included accessories.
All returned items must be approved and issued an RMA number (returned merchandise authorization). No credit will be issued without a RMA number.
Items must be properly packaged for shipping. We reserve the right to charge a restocking fee or decline issuance of credit for damaged retail packaging. Customer is responsible for return shipping fees.
Please use a trackable service for you return such as UPS, FedEx, or certain USPS services. Return shipments should be insured for the proper amount. Bleeding Tarmac will not be held responsible for returns that are lost or damaged in shipping.
Once the item is received and inspected, a credit will be issued. Refunds may take 3-5 business days to post on your account.
All refunds are subject to a processing and/or restocking fee.
No returns on the following: Special order items, helmets, clothing articles, items considered clearance or close-outs, or items with special pricing, are final sale and may not be returned.
Apparel and promotional items
All apparel and promotional items, including hats, t-shirts, sweatshirts, stickers... are final sales. No returns, exchanges, or refunds will be issued on these items.
We offer no warranty above that of the manufacturer of goods sold. In an effort to minimize legalese we offer the following statement. Each brake parts manufacturer warrants it's goods to be fit and free from defects in materials and workmanship. This is quite limiting. Any warranty above and beyond that is strictly on a case by case basis and limited to replacement of equal value only.
Coupon codes can only be redeemed at the time of purchase. Once an order is placed we will not price match any other competitors, all price matching must be negotiated before an order is placed.
We reserve the right to refuse any order for whatever reason, without being liable for any damage or costs.
Most products on our websites are designed for off-road use, and to be used at the purchaser’s own risk and discretion. Bleeding Tarmac, Broken Motorsports, or any of its companies are exempt from any liability, and will be held harmless for any damage incurred, either property damage or personal harm, by the use of any of these products, whether being used for off-road use, or for use on public roads. While some of these products may be legal for use on public roads, Bleeding Tarmac, Broken Motorsports, or any of its companies do not endorse, authorize, or sanction their use on such public roads.